How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
How do you really feel in relation to How to Install a Bathtub?
Mounting a bathtub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is easily available, the job can relocate rapidly; if you need to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a new tub in your shower room if you have already gotten a new tub as well as don't need to change the arrangement of your previous water system pipes.
Your tools as well as product list need to make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the faucet as well as the sink. Secure the faucet in place with the manufacturer offered backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type needs to be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the bath tub in the needed placement. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the tub up until the spirit level reads level.
To mount taps, fit the bottom of the outermost adaptable faucet port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the supply of water as well as check all joints as well as new pipework for leaks and also tighten them if required. Fill the bath tub and likewise examine the overflow electrical outlet and also the regular outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub ought to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Getting ready for the Installment
First of all, the sustaining framework provided with the bathroom ought to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very interested by How to Install a Bathtub and I hope you enjoyed my blog entry. Remember to take the opportunity to promote this blog post if you enjoyed reading it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Additional Resources
Report this page